Tuesday, December 8, 2009

Make your own peasant top






Bodice front and back

A-B= ½ shoulder+¼”
A-P =length of the top +1½’
A-O = 1/12th chest
A-H =1½”
A-L =1/12th chest+1½”
A-C =¼chest-1”
Draw perpendiculars from C and P
C-E= ¼ chest +1”+½”
C-D =A-B
Join B-D
Mark F on the line B-D such that D-F =1”
Join O-H and O-L back and front neck shapes as shown in the figure. Mark G such that O-G = 1”
Join G-F and produce. From the point E draw a perpendicular E-N to the line G-F produced.
Produce E-N to M such that N-M =E-N
Shape E -F-G as shown in the figure LIPK is extra material 2” wide for gathers in front. And HIPK is extra material 2” wide for gather at the back. Width can be increased or decreased according to taste.

sleeve

A-B= ½ shoulder+¼”
A-O = 1/12th chest or to taste
A-H =1½”
A-L =1/12th chest+1½”or to taste
A-C =¼chest-1”
Draw perpendiculars from C
C-E= ¼ chest +1”+½”
C-D =A-B
Join B-D
Mark F on the line B-D such that D-F =1”
Join O-H and O-L back and front neck shapes as shown in the figure. Mark G such that O-G = 1”
Join G-F and produce. From the point E draw a perpendicular E-N to the line G-F produced.
Produce E-N to M such that N-M =E-N
B-R = sleeve length +2"
R-Q = sleeve width+1/2"
Join M-Q.
Shape M-F-G as shown in the figure
SRTO is extra fabric ,O-T =S-R= 2" wide for gathers. It can be varied according to taste.

Photobucket

Monday, November 23, 2009

Method of drafting and cutting for beginners


When there are identical parts usually pattern is drafted on folded paper. For example right and left sleeves front and back of bodice etc…. Both the shapes of front and back such as neck, armhole etc……are marked on the top fold itself. Outer line is cut first .Sheets are separated. This forms the back. On the top sheet the inner lines are also cut .This forms the front. Care should be taken to measure from the fold line. Facing line for neck, armhole etc …can also be marked .position for darts can also be marked.
Precautions to be taken while cutting the material.
1. It is better to shrink cotton material before cutting or ½’ extra should be added for width.
For the length we can add still more. It depends on the material. I prefer to wash, iron and
then cut the pattern.
2. Straighten the grain of the fabric by pulling the corners material .If the fabric is long you need help of another person. Lay the fabric on a table keeping both the selvedges together. If it forms a rectangle and the warf and weft are perpendicular it means fabric is grain perfect. Sometimes shopkeepers also would have cut the fabric bias. That also should be corrected. Pull a thread from width wise from end to end and cut on the line got by pulling the thread.
3. Fabric should be ironed lengthwise. Length wise means the grains that run parallel to the selvedge.
4. Selvedges should always come to sides .(side of the sleeve, side of the bodice etc…..)If the garment is stitched width wise it will not stretch. It will be uncomfortable to wear. Dresses get torn fast.
Measure the width of the draft and fold the material according to that. Keep the fabric on table and smoothen it so that there are no folds. Place the large pieces of the paper draft first. Check whether the garment has back opening or front opening. Keep the one that has got no opening on fold line. Selvedges should come to the sides. Arrange the other small pieces .Pin the pieces to the fabric without lifting the fabric.If there is not enough fabric to cut same pieces together cut them separately. Mark darts and notches and then remove the pins.

Photobucket

Pattern making(for begginners)

Making a paper pattern is a must for the beginners. I prefer to make paper patterns and then cut the fabric. It saves time and material and the paper draft is reusable. We can adjust the placing of the paper pattern on the fabric according to the material available. If the fitting is not good we can make necessary alterations in the paper pattern itself. Same paper pattern can be used as basic and design different patterns
Materials needed
1. Sheet of paper.
We need thick sheet of paper if we want keep the draft for a long time and use it again and again. If not news paper is well and good. Once we get correct fitting we can make cut pattern in thick cardboard and use it for future use.
2. Pencil
3. Eraser
4. Ruler
In the paper pattern ½” seam allowance will be there unless it is mentioned.name of the parts should be written .If two identical parts are cut separately we have to mark R and L on the draft. For example sleeves. Especially while cutting plain material we end up cutting two right sleeves.
½” seam should be added to attach button stands. If we have ample material button can be cut along with the bodice. Care must be taken to mark the place by notches from where the button strand starts. Notches should be made to mark important points that must coincide while stitching. The point of notch should project beyond the cutting line of the pattern.


Photobucket

Friday, November 20, 2009

Puff sleeves with gathers at the top only




Swing the sections apart at the cap line only keeping the sleeve edge together.Give shape as shown in the figure . We get gathers, only at the cap of the sleeve.

 Another method

Puff sleeves with gathers at bottom only




By spreading the sections only at the bottom as shown in the figure sleeves will have gathers only at the bottom .

puff sleeves with more fullness






Plenty of fullness at top and bottom of the sleeve can be obtained by making more sections and spreading them apart Mid line of the sleeve is extended both ways
as shown in the figure 2. Shape is given as shown.

Thursday, November 19, 2009

Varieties of puff sleeves from plain sleeve


Here are a few varieties of puff sleeves.